POD14B — Dual Analog To Digital Converter

DIGITAL REFERENCE INPUT

Input Impedance 75 Ohm or 110 Ohm Input Level 0.2-7V p-p Sampling Frequency Range 32kHz to 192kHz

ANALOG AUDIO INPUT

Converter 1:

Input Impedance 47 kOhm unbalanced Maximum Input +14dBu Frequency Response +0.01/-0.26dB, 20Hz to 20kHz Converter 2:

Input 2 Impedance 24 kOhms balanced Maximum Input +24dBu Frequency Response ± 0.1dB, 20Hz to 20kHz

DIGITAL AUDIO OUTPUT

Resolution 24 bits Output Standard AES/EBU 75 Ohm unbalanced and 110 Ohm balanced External Sampling Frequency 32kHz to 192kHz Internal Sampling Frequency Selectable 32, 44.1, 48, 96 and 192kHz Jitter less than 5ns Level (75 Ohm) 1 V p-p terminated Level (110 Ohm) 3 V p-p terminated Noise better than -110 dBFS, 20Hz to 20kHz Typical unweighted Total Harmonic Distortion + Noise better than 0.02%

All the preceding specifications were taken with a 48 kHz external reference.

Also: specs boilerplate (56 devices)

Front panel controls and tallies include a power switch with LED tally, a momentary step switch and LED indicators to cycle through the internally generated sample rates from 32 to 192 kHz. Two LEDs indicate whether the external or internal reference is used. The external reference signal has precedence over the internally generated reference signal. As soon as an external reference signal is detected POD14B will automatically switch to it. Coarse gain controls for input 1 are also available on the front panel.

REAR PANEL

Connections to the POD14B are made on the rear panel. Input 1 accepts unbalanced analog signals via standard RCA connectors. Input 2 accepts balanced analog signals via 3-pin Phoenix® pluggable connectors. Connections to the digital reference may be made by either 75Ω BNC or 110Ω Phoenix® 3-pin pluggable connectors. Both the 75Ω and 110Ω connections of each output may be used in parallel. Fine level trim controls for the analog input signal are located adjacent to the corresponding input connectors. The AC power receptacle and fuse are also located on the rear panel.

SETUP

There are no special setup procedures necessary prior to using POD14B. Simply plug the unit into an AC power outlet and connect input and output cables. POD14B is factory calibrated to output a nominal -20dBFS AES/EBU signal. Apply a -10dBu signal to input 1 or a +4dBu signal to input 2. Both converters may be used in tandem. One or both output connections of each converter may be used in tandem. The input trim controls may be used to set POD14B up for a different nominal digital output signal

(only shared text)

Also: warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (68 devices)

(only shared text)

Also: warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (67 devices) · warranty boilerplate (68 devices)