M901C — Stereo Line Input Module

M901C STEREO LINE INPUT MODULE

Input Sensitivity: -10 to +10 dBu. (ref. 600 ohm source).

Frequency Response: +/-0.2 dB from 20 Hz to 20 kHz. Measured at direct output.

Noise: Greater than 80 dB below nominal operating level, with the attenuator set for 15 dB "in hand" ( 20 Hz to 20 kHz).

Harmonic Distortion: Less than 0.05% from 20 Hz to 20 kHz at 10 dB above operating level.

Source Impedance: 600 ohms or less balanced.

Input Impedance: 30,000 ohms, balanced.

Output Impedance: Less than 60 ohms at insert and direct outputs.

Load Impedance: Greater than 10K balanced at insert and direct outputs.

Output Level: -6 dBu nominal, unbalanced.

Logic Input Levels: Logic 0: 0 to +1.75 volts dc. Logic 1: +3 to +24 volts dc.

External Control Output: Open Collector. Minimum Load Impedance: 600 ohms. Maximum Load Current: 30 mA. Maximum Supply Voltage: +24 volts dc. Saturated Collector Voltage: +2 volts maximum at 30 mA load.

Power Requirements: +/-24 volts dc, 150 mA.

Ambient Temperature: 0 to 50 degrees Celsius.

Weight: 750 grams.

The M901C provides the line level stereophonic input channel facility for the Renaissance series of radio consoles.

The input source selector allows two separate stereo inputs to be connected to the input module. Each input has its own preamplifier, allowing individual gain trimming and common mode balancing of the discrete source inputs.

The sensitivity controls are front panel accessible. These continuously variable controls provide adjustment for input source levels from -10 to +10 dBu. A mode selector is provided which gives the operator the ability to reconfigure the stereo source material in the following manner.

1) Provide normal stereo.

2) Feed the left input channel only to both the left and right outputs.

3) Feed the right input channel only to both the left and right outputs.

4) Combine the left and right outputs into a left plus right mono output.

The preamplifier outputs, once selected, appear at the module connector for the insertion of optional processing.

The cue buss feed is connected to the insert return line so that pre-fade listening of source material can take place before any input module level control.

Direct left and right channel outputs are provided at the module connector. These direct feeds may be optionally used for multitrack applications or to feed the console mix-minus system.

The output from this module may be assigned to any or all of four stereo program busses. These buss selectors are preceded by a centre detent balance control, giving the operator the ability to trim level imbalances between the left and right channel signals.

Two auxiliaries are also integral to the module, a monophonic and a stereo one. Both are assignable individually pre or post VCA, and each auxiliary has it's own level control and on/off control.

The module also contains a "blind assignable" monophonic post VCA buss output. This buss may be utilized for use by the console mix minus system.

Unitary control of most module functions is also available at the module connector for machine control as well as external control inputs.

Outgoing control signals are furnished as open collector paths to control common when activated. Comprehensive internal module logic allows intelligent control of external machines, with all outgoing control signals following module source selection (source A or B).

A momentary closure to control common (through an open collector transistor), is provided when the module is turned on or off for both the A or B source. This totals four independent outputs, one start and stop signal for both the A and B module sources.

An additional sustained closure to common is provided for both the A and B input sources. This closure is active when the main channel is on, and is provided for external use. These outputs are also internally assignable to one or all of three internal console muting busses. These busses run to the M905 monitor modules in the console system for muting the monitor speakers.

The internal buss structure of the console includes a cue control buss. If a module is assigned to this buss, putting the module into cue will activate the auto cue function in the M905A control room monitor module.

The lamp internal to the channel off button is uncommitted and is brought out on the module connector. This is intended for utilization as a tally indicator for external machinery.

Module control inputs are also configured to activate when a closure to control common is provided. The module can be turned on and off, the cue can be toggled, and the source can be selected between A and B by simply grounding the appropriate module connector pin.

Program buss assignment is also possible external to the module. Again, a closure to control common will effect this assignment. To change a previous buss assignment, the electronic latches require clearing before loading them with new buss assignments. A closure to common will also perform this function.

External control of the VCA within each module is also brought out to the edge connector. Application of a voltage between 0 and 5 volts DC will bring the attenuator from no external attenuation to full attenuation from the current fader position. This feature can be of benefit for automated cross-fading.

The M901C Stereo Line Input module is packaged in a 1.5" wide x 16.2" high x 6.6" deep space.

This module derives its power from the console system bipolar +/-24 volt power supplies. 1) Source "B" Select

Depressing this momentary switch (SW2), enables the "B" input source and disables the "A" input source selection (if it was selected). Double pressing the active switch will cancel the selection.

2) Source "A" Select

Depressing this momentary switch (SW1), enables the "A" input source and disables the "B" input source selection (if it was selected). Double pressing the active switch will cancel the selection. This source is select

Also: specs boilerplate (5 devices)